Article

Banerjee, A.J. and Roy, H. and Biswal, M.K. and Lohar, A.K. and Chattopadhyay, H. and Naga Hanumaiah, Naga Hanumaiah (2017) Investigation on Tensile Behaviour of Laser Welded Al–Mg–Sc–Zr In Situ TiB2 Reinforced Metal Matrix Composite. Transactions of the Indian Institute of Metals, 70 (8). pp. 2071-2077.

Mishra, Srimant Kumar and Roy, H. and Mondal, A.K. and Dutta, Krishna (2017) Damage Assessment of A356 Al Alloy Under Ratcheting–Creep Interaction. Metallurgical and Materials Transactions A, 48 (6). pp. 2877-2885.

Shukla, N. and Roy, H. and Show, B.K. (2016) Effect of prior austempering heat treatment on the microstructure, mechanical properties and high-stress abrasive wear behaviour of a 0·33% C dual-phase steel. Canadian Metallurgical Quarterly , 55 (1). pp. 13-22.

Ghosh, D. and Roy, H. and Das, S. and Mitra, S.K. (2016) Nanostructured CeO2 coating for high temperature oxidation protection. Surface Engineering, 32 (6). pp. 397-403.

Thadela, S. and Mandal, B. and Das, P. and Roy, H. and Lohar , A.K. and Samanta, S.K. (2015) Rheological behavior of semi-solid TiB2 reinforced Al composite. Transactions of Nonferrous Metals Society of China, 25 (9). pp. 2827-2832.

Ghosh, D. and Ray, S. and Mandal, A. and Roy, H. (2015) Failure Investigation of Radiant Platen Superheater Tube of Thermal Power Plant Boiler. High Temperature Materials and Processes, 34 (2). pp. 171-175.

Ghosh, D. and Ray, S. and Roy, H. and Mandal, N. and Shukla, A.K. (2015) High-Temperature Graphitization Failure of Primary Superheater Tube. High Temperature Materials and Processes, 34 (8). pp. 777-781. ISSN 0334-6455

Ghosh, D. and Ray, S. and Roy, H. and Shukla, A.K. (2015) Investigation into Cause of High Temperature Failure of Boiler Superheater Tube. High Temperature Materials and Processes, 34 (2). pp. 141-146.

Goyal, H. and Mandal, N. and Roy, H. and Mitra, S.K. and Mondal, B. (2015) Multi Response Optimization for Processing Al–SiCp Composites: An Approach Towards Enhancement of Mechanical Properties. Transactions of the Indian Institute of Metals, 68 (3). pp. 453-463.

Ghosh, D. and Roy, H. and Mitra, S.K. (2015) Nanostructured Y2O3 plasma coating for high temperature oxidation protection. Journal of Adhesion Science and Technology, 29 (10). pp. 954-964.

Saha, Atanu and Roy, H. and Shukla, A.K. (2014) Failure of a pendent reheater tube in a 110 MW thermal power plant. High Temperature Materials and Processes, 33. pp. 299-304.

Roy, U. and Roy, H. and Daoud, H. and Glatzel, U. and Ray, K.K. (2014) Fracture toughness and fracture micromechanism in a cast AlCoCrCuFeNi high entropy alloys ystem. MaterialsLetters, 132. pp. 186-189. ISSN 0167-577X

Barat, K. and Bar, H.N. and Mandal, D. and Roy, H. and Sivaprasad, S, and Tarafder, S. (2014) Low temperature tensile deformation and acoustic emission signal characteristics of AISI 304LN stainless steel. Materials Science & Engineering A, 597. pp. 37-45. ISSN 0921-5093

Shukla, A.K. and Das, P. and Dutta, S. and Ray, S. and Roy, H. (2013) Failure analysis of a head gear pulley used in coal mines. Engineering Failure Analysis, 31. pp. 48-58. ISSN 1350-6307

Roy, H. and Ray, A. and Barat, K. and Hochmuth, C. and Sivaprasad, S. and Tarafder, S. and Glatzel, U. and Ray, K.K. (2013) Structural variations ahead of crack tip during monotonic and cyclic fracture tests of AISI 304LN stainless steel. Materials Science & Engineering A, 561. pp. 88-99. ISSN 0921-5093

Samanta, S.K. and Das, Prosenjit and Lohar, A.K. and Roy, H. and Kumar, S. and Chowdhury, A.K. (2013) A novel approach of manufacturing Nickel Wicks for loop heat pipes using Metal Injection Moulding (MIM). Sadhana, 38 (2). pp. 281-296.

Roy, H. and Sivaprasad, S. and Tarafder, S. and Ray, K.K. (2012) Cyclic fracture behaviour of 304LN stainless steel under load and displacement control modes. Fatigue & Fracture of Engineering Materials & Structures, 35 (2). pp. 108-113.

Mandal, Nilrudra Mandal and Roy, H. and Mondal, B. and Murmu, N.C. and Mukhopadhyay, S.K. (2012) Mathematical Modeling of Wear Characteristics of 6061 Al-Alloy-SiCp Composite Using Response Surface Methodology. Journal of Materials Engineering and Performance, 21 (1). pp. 17-24. ISSN 1059-9495